Drunk butterfly pot planting and maintenance method : Seedlings should be transplanted with time, with 2-3 true leaves, planted or potted in June, straight rooted plants, small roots, difficult to recover after transplantation, usually in the open field in spring, or when the seedling grows to about 5 cm high Transplanted and transplanted in fertile soil. Generally, there is no need to apply fertilizer. During the growing season, fertilize once every half month. During the growth period, water and fertilizer should be controlled to prevent the plants from growing and affecting flowering. Flower bud formation and flowering period, applying fertilizer 2 to 3 times, can extend the flowering period. Usually watering to maintain a half-baked state is good, always watering when drought. When the flower is blooming, it is necessary to set up pillars to prevent lodging. If there is no seed, it is necessary to cut off the residual flowers in time after the flower is thanked, so that the seeds are not allowed to be seeded, and the nutrient consumption is reduced, so as to prolong the flowering period. The whole plant has sticky hair and consumes less water. Besides the need for more water during the flowering period, the seedling stage can be poured or less watered, which is easier to manage. Watering at least once a day in the summer, in case of high temperature and drought, you can move to a cool place, and then fill the water after the basin is slightly cooler. In autumn and winter, the amount of water can be reduced, and the surface of the potting soil is re-watered when it is dry. Light temperature Cleome prefers high temperature and heat resistance. The most suitable growth temperature is 20 ° C to 32 ° C. It is good for light and can grow under semi - negative conditions. However, in order to make it dwarf, it is necessary to see direct light as much as possible. It is better to take more than 4 hours a day. When planting flower beds, the residual flowers should be removed in time so that they do not knot to prolong the flowering period. For potting, the top buds are removed at the seedling stage, and the nitrogen fertilizer is controlled to dwarf the plants. For cut flowers, the planting can be slightly dense, and the lateral buds are removed to promote the development of the top buds. If you want to make Cleome flower bloom in the Spring Festival, you can plant it in the autumn and move it into the indoor sunny place before entering the winter. The indoor temperature should be maintained at about 20 °C. The soil is kept slightly moist, and the bud period needs to be applied 2 to 3 times. Compound liquid fertilizer can bloom during the Spring Festival. There are often leaf spot and rust hazards. Leaf spot is sprayed with 50% Tolkin WP 500 times solution, and rust can be treated with 50% rust-free WP 3000 times liquid spray. Thin wall ball bearings are simple in structure and easy to use. Mainly used to bear radial load, but when the radial clearance of the bearing is increased, it has a certain performance of Angular Contact Ball Bearing and can bear combined radial and axial load.
Thin wall ball bearings have a bearing inner diameter and outer diameter ratio less than a specified value. The ratio of bearing outer diameter to bearing inner diameter is 1.25 or less. It is called thin wall ball bearings, which means that the outer diameter-inner diameter value of the bearing is very small and the bearing wall is very thin. Thin Wall Ball Bearing,Thin Section Bearings,Thin Ball Bearing,Thin Wall Bearing Shijiazhuang Longshu Mechanical & Electrical Equipment Trading Co., Ltd. , https://www.longsbearings.com
When the speed is high and thrust ball bearings are not suitable, thin wall ball bearings can also be used to bear pure axial loads. Compared with other types of bearings of the same size, this type of bearing has a small friction coefficient and a high limit speed. But it is not impact resistant and not suitable for heavy loads.
The precision required by thin wall ball bearings is very high, because the wall is very thin, so the weight it can carry is also very low, and the impact resistance is very poor, so this must be selected according to the use environment!
Characteristics
The specific use of thin wall ball bearings:
Model airplanes, remote control cars, machine tools, motors, water pumps, agricultural machinery, textile machinery, laser printers, instruments, measuring instruments, electronic accessories, motors, motors, etc.
Welcome to contact me to get the price of thin wall ball bearings!