March 28, 2024

What are the cabinet processing processes? Cabinet processing details

For many friends who choose to buy cupboards, they all want to know the processing of cabinets , so that we can clearly know where to find defects when choosing cabinets. Today, we look at the process of cabinet processing with Xiaobian. And cabinet processing details.

Cabinet processing - material selection

To make a good cabinet must have a good plate as a basis. At present, the market generally uses veneer and stainless steel plate as the cabinet plate of the cabinet. The base material of the veneer is generally particle board or density plate, high temperature resistance, hard texture, pressure resistance, acid and alkali resistance, most cabinet cabinets use plywood . Jie Ge cabinet general told reporters that the environmental requirements of the cabinet industry mainly refers to the formaldehyde emission of the cabinet plate, according to the test method specified by the national standard, E1 standard formaldehyde emission ≤ 1.5mg/L, E2 standard formaldehyde emission ≤ 5.0mg/ L. Among them, the E1 sheet can be used directly in the room. The E2 sheet must be surface treated before it can be used indoors. The materials used in the cleaning cabinet are all imported from Germany and belong to the E0 standard. The environmental safety index far exceeds the national standard.

Cabinet processing - cutting

Cutting is the first step in the production of cabinets. The so-called cutting is to cut the entire large plate. The equipment used in this step is generally an electronic open saw. Workers told reporters that generally speaking, the opening of materials is only the first step, and the finished board must continue to be processed in the following process. However, many manufacturers' backing boards usually have only one process for opening materials. .

Cabinet processing - slotting

In the current production of cabinets, the plates to be processed in this process include: bottom plates, side plates, and battens, since the current process almost always uses the side plates and the bottom plate to clamp the back plates, so the side plates and the bottom plates are required. The slotting process is performed so that the back plate can be inserted into the side plate and can be stably placed on the bottom plate, so the bottom plate and the side plate are to be grooved. Grooving equipment is generally manual slotting saws (manual sliding table saws), because the slotting speed is fast, generally experienced workers, one person can open a thousand pieces a day, enough to meet the factory's production capacity. For one-time forming, the serrations of slot saws are generally the same width as the thickness of the back plate purchased by their own factory.

Cabinet Processing - Edge Sealing

Almost all components in the production process of the cabinet are subjected to edge-sealing processing steps. The reporter also learned from the chat with the workers that due to the improvement of the quality of the craft, the three sides of the formerly sealed parts (where the board and the board were in contact can be sealed, because the first one cannot be seen, and the second one is to connect the holes, Destroy the edge. Now all four sides. The machine used in this process is a double-end milling machine, and many of them go to the cabinets to save the cost. There are two purposes of plate edge milling. One is to make the plate size more accurate, and the other is to make the four sides of the plate more smooth and smooth.

Cabinet processing - punching

Punching a seemingly simple process is actually one of the most error-prone processes, because this process involves all the connections between the plates. If there is a slight deviation, it may cause the connection between the two components. On the other hand, even the third component is not connected, causing all the previous processes to do no work, so the most critical step is also the process. During the live demonstration of the workers, the reporter learned that the main equipment for punching is six rows of drills, three rows of drills, etc. Six rows of drills are not six rows in one direction, but four rows of upper and lower rows, two rows of left and right, so that they can be played at one time. System and structural holes.

Cabinet processing - cabinet combination

Finally, the last step, Ge told reporters that the cabinet is generally used to connect the wooden needle, the wooden needle coated with glue, into the hole in the sheet to open a good, a few boards easily connected together. Then use the furniture combiner and apply pressure from all sides at the same time so that the cabinet is finally formed. It can be said that the cabinet thus produced is structurally stable.

The relevant information about cabinet processing was introduced here for everyone. I hope this article will be helpful to everyone. If you still have something you don't understand, you can leave a message to Xiaobian at the bottom. We will answer your questions as soon as possible.

Cabinets Kitchen Cabinets Custom Cabinets Stainless Steel Cabinets Cabinets

Office Partition Aluminium Profile

The Aluminum Office Partition has the characteristics of lighting, soundproofing, fireproofing, environmental protection, convenient installation, reusable and mass production. The aluminium office partition is fashionable, elegant and generous. It is a partition that can divide the space and is superior to the traditional partition wall. The aluminum alloy partition is divided into two kinds of glass high compartments and single glass high compartments. The combination of a variety of glass and aluminum alloy is more elegant and beautiful.


Material Grade: Aluminum Alloy 6000 series:6063,6061,6060,6005
Temper: T3-T8
Finish: Anodised, powder coated, sandblasting, electrophoresis ,Powder coating, Polish, Brushed, PVDF coating, wood-grained etc.
Color: Silvery white, black, golden, champagne, dark bronze or according to your requirement
Shape: Square, Round, Flat, according to  customers' drawings
Thickness: Above 0.7mm,the thicker the better
Specification:    

A.    Length: ≤6.5m
B.  Normal Wall thickness: ≥1.0mm
C.  Normal Anodizing thickness: ≥8µm
D.   Normal powder coating thickness: 60-120µm
E.  Tensile strength: ≥160mpa
F.  Yield strength: ≥110mpa
G.    Extensibility: ≥8%
H.    Hardness(HW): 8-15

Packing details: Kraft paper, EPE Fram, Shrink film, Composite paper or as your need
MOQ: 500kg
Delivery time: Normally20-25days for a 40ft container after we confirm your deposit.

Normal order sequence:
    
1. Confirm the drawings, colors and price
2. Pay the mould fee and we start to make moulds
3. We send samples to you for your confirmation
4. Make the payment of 30% deposit, start production
5. Delivery  

aluminium profile office partition


Office Partition Aluminum Profile

Office Partition Aluminum Profile,Aluminum Office Partition,Aluminum Partition Wall,Aluminium Section Partition

Zeyi Aluminum Co., Ltd. , https://www.zeyialuminum.com